Products
Glass-Fiber-Reinforced POM
  • Glass-Fiber-Reinforced POMGlass-Fiber-Reinforced POM

Glass-Fiber-Reinforced POM

Zhongwang, reliable Chinese supplier for bulk sourcing Glass-Fiber-Reinforced POM, supplies virgin glass-filled polyoxymethylene pellets for global B2B high-load structural-component purchasers. Our glass fiber reinforced POM covers GF10%, GF20%, GF25%, GF30% short-glass-fiber grades based on both homopolymer POM-H and copolymer POM-C matrix, delivering greatly improved rigidity, creep-resistance, heat-deflection performance and reduced mold shrinkage, widely used for heavy-duty gears, bearing sleeves, pump components, automotive structural parts and high-strength wear-resistant inserts by injection molding.

    For heavy-load plastic components, Glass-Fiber-Reinforced POM procurement through Zhongwang begins with the required deflection limit and the contact conditions of the finished part. The material combines short glass fibers with polyoxymethylene to increase stiffness and resistance to deformation relative to suitable unfilled acetal grades.

    The fibers reinforce the polymer matrix but also change how the component behaves during molding and in service. Flow-oriented fibers can create directional differences in strength and shrinkage. Greater reinforcement may improve rigidity while reducing impact toughness and making the surface more abrasive.

    Consequently, the highest glass-fiber percentage is not automatically the best grade for every gear, sleeve or structural insert. The choice depends on whether the component's main failure risk is bending, long-term creep, impact, frictional wear or dimensional variation.

    Choosing Reinforcement by Mechanical Duty

    GF10: Moderate Stiffness with Fewer Compromises

    Ten-percent glass-fiber grades are a starting point for medium-load brackets, instrument supports and selected mechanical components where some reinforcement is required without prioritizing maximum rigidity.

    The reference flexural modulus is 4,000–5,200 MPa, with heat deflection temperature around 130–140°C at 1.82 MPa. These are grade-family values, not guarantees for every matrix option.

    GF20 and GF25: Components Under Higher Load

    These reinforcement levels offer a stronger stiffness and creep-resistance emphasis for automotive lock assemblies, mechanical supports, pump housings and selected transmission parts.

    The reference flexural modulus is 5,500–7,000 MPa and heat deflection temperature is 145–155°C at 1.82 MPa. Check the actual grade's impact and dimensional properties when selecting these compounds.

    GF30: High Rigidity with Additional Design Constraints

    Thirty-percent reinforcement is intended for applications prioritizing high stiffness and dimensional resistance under load. The supplied reference lists flexural modulus of 7,200–8,500 MPa and heat deflection temperature of 150–160°C at 1.82 MPa.

    Higher fiber content may make surface appearance, flow behavior, directional shrinkage, impact toughness and tool wear more difficult to manage.

    The Trade-Off That Matters in Moving Parts

    Unfilled POM is valued for sliding and wear-related applications. Reinforcing it with glass fiber changes the tribological behavior of the contact surface.

    Exposed or surface-near fibers may increase abrasion against a mating shaft, metal surface or plastic counterpart. This means a reinforced gear, bearing sleeve or slider should not automatically be assumed to have better frictional performance because it has greater strength.

    For components with continuous sliding contact, evaluate the mating material, surface pressure, speed, lubrication and wear rate. Low-friction modified glass-filled grades may be considered if supported by the selected formulation.

    Choosing Between POM-H and POM-C Matrices

    Matrix Option Selection Priority Considerations
    POM-H-Based Compound Mechanical strength, rigidity and cyclic loading in suitable dry environments Higher sensitivity to some hot-water and chemical conditions
    POM-C-Based Compound Water-exposed pump or valve components and broader chemical-service considerations Mechanical properties and creep performance remain grade-dependent

    Technical Specifications

    Parameter Reference Data
    Product Name Glass-Fiber-Reinforced POM
    Brand Zhongwang
    Polymer Matrix POM-H or POM-C
    Reinforcement Short Glass Fiber
    Glass Fiber Content 10% / 20% / 25% / 30%
    Density 1.47–1.60 g/cm³
    MFR 2–8 g/10 min (190°C/2.16 kg), grade-dependent
    Flexural Modulus 4,000–8,500 MPa, grade-dependent
    Heat Deflection Temperature 130–160°C at 1.82 MPa, typical reference
    Notched Izod Impact at 23°C 5–8 kJ/m², typical reference
    Shrinkage Along Flow 0.4–0.8%, reference
    Shrinkage Across Flow 0.8–1.2%, reference
    Appearance Black or Natural Opaque Pellets
    Processing Injection Molding
    Packaging 25 kg Moisture-Protected Woven Bag
    Technical Documents TDS, COA, SDS and Applicable Mechanical Test Reports

    Injection Molding: Fiber Direction Is Part of the Design

    The gate location and melt-flow path affect fiber orientation. Since reinforced compounds may shrink differently along and across flow, tooling designed for an unfilled material may require dimensional review before conversion.

    Excessive screw shear can shorten reinforcing fibers and change the molded component's properties. Tooling wear and fiber-related surface marks should also be monitored in repeat production.

    The supplied processing reference lists barrel temperatures around 190–210°C. Overheating or excessive residence time can decompose the POM matrix and release hazardous formaldehyde-containing fumes; follow grade-specific safety and processing guidance.

    Although the material has relatively low moisture absorption, surface condensation can produce molding defects. The reference suggests conditioning or drying at 80°C for 2–4 hours when necessary, subject to actual grade instructions.

    Production Qualification for Structural Parts

    A meaningful trial should compare the original and reinforced components under the same loading conditions. Measure deflection, dimensional change after molding, performance after sustained stress and any wear at mating surfaces.

    For a Glass-Fiber-Reinforced POM bulk quotation, Zhongwang can coordinate grade discussions using the required matrix, reinforcement percentage, component drawing, expected mechanical load, operating medium and estimated purchase volume.

    Availability of samples, TDS, COA and supporting mechanical data should be established for the specific grade before production release.

    FAQ

    Does higher glass fiber content always improve acetal gear performance?

    No. Higher fiber loading generally increases rigidity, but it can also affect impact toughness and abrasive wear against mating components. Test the complete gear assembly under the actual contact conditions.

    Why can reinforced POM warp even though its shrinkage is lower?

    Fiber orientation creates directional shrinkage differences. Uneven flow, wall thickness and cooling can cause warpage despite reduced overall shrinkage.

    Which base matrix is better for wet pump components?

    POM-C-based grades are commonly preferred for improved hydrolysis-related performance. Confirm compatibility with the actual fluid and operating temperature.

    Is a reinforced acetal grade suitable for an unlubricated bearing?

    It requires careful evaluation. Exposed glass fibers may increase wear on the counterface, and an unfilled or specially modified low-friction compound may perform better.

    What should buyers specify for structural reinforcement?

    Provide the load and deflection requirements, base-matrix preference, glass-fiber percentage, temperature, fluid exposure, component geometry and tolerance requirements.

    Send Inquiry
    Contact Info
    • Address

      Building 1, China Plastics International Business Center, No. 285 Shunda West Road, Yuyao City, Ningbo City, Zhejiang Province, China

    If you have any enquiry about quotation or cooperation, please feel free to email us or use the following inquiry form.Our sales representative will contact you within 24 hours. Thank you for your interest in our products.

    X
    We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
    RejectAccept